For heat insulation SUS416
WASHERS (RISER PADS)
URETHANE WASHERS
25
UW
Applicable bolt size d
t
M 6 M 8 M10
6.2 3.5 8.2 4.6 10.2 5.7
E Although urethane itself has a heat resistant temperature of 100°C, when used continuously its durability falls, so use it at a temperature of no more than 80°C.
RPSK (Dowel pin type)
RPST (for countersunk bolt)
RPSB (Bolt fixing type)
C0.3
C0.3
C0.3
C0.3
C0.3
C0.3
V H7
Applicable bolt size d M 6 7 M 8 9 M10 11 M12 13 M16 17
0 - 0.5 + 0.4 + 0.1
8
+ 0.015 0 + 0.018 0
d
10 12 13
0 - 0.3
T
D
H Hardness Shore D58
0 + 0.1
- 0.1 0 0 + 0.1
d
+ 0.2 + 0.1 T ± 0.1 t
V H7
d
- 0.1 0
■ Urethane hardness characteristics comparison (comparison with Shore A95) Characteristics Unit Shore D58
+ 0.1 + 0.2
+ 0.1 + 0.2
D
- 0.1 0
Part Number
T
T
D
D
D
d
T
Type
d
M Material SUS416
M Material SUS416
M Material SUS416
Shore A95
10 13 16 20
16 18 24 27
10 13 16 20
Tensile Strength
MPa
47.8
39.2
Part Number
Part Number
Part Number
Applicable bolt size (M) Selection
Applicable bolt size (M) Selection
V
T
T
T
%
Elongation
440 153
400 107
Type
D
Type
D
Type
D
1.5 3
UW
Tensile Breakage Strength Impact Resilience Compression Set Heat–resistant Temperature
kgf/cm
25
8 10
25 6 8 10
30
6
8
% % ℃
53 39
40 45
10 15 20
RPST
10 15 20
10 15 20
100 80 E The above value is the reference value. It is not a guarantee value.
RPSK
RPSB
40
6
8
10
30
8 10 12
30
8 10 12 16
Part Number – T UW10 – 1.5
Order
40
10 12
13
40
8 10 12 16
Stop bolt STBG ( P.915 )
UW
Quotation
Part Number – V/M – T RPSK30 – V12 – T15 RPSB40 – M12 – T20
Delivery
Applicable bolt size d d 1
h M 6 6.2 11 6.5 M 8 8.2 14 8.6 M10 10.2 17.5 10.8 M12 12.2 20 13
Order
Fixed side molding plate Runner stripper plate Selection side plate
Example Use for sound proofing when the mold is being opened.
Delivery Quotation
RPSZ (Counterbore type)
d 1
C0.3
C0.3
Fixed side molding plate
Part Number – V,M – T –
(MK/TK1/TK2/TK3)
Puller bolt PBTN ( P.917 )
Alterations
UW
MK
RPSZ30 – M8 – T15 –
Alterations Code
Spec.
Adds a groove on both sides in order to facilitate insulation. X Express services not available
● When using a urethane washer on the stopper bolt, be careful of the forming dimension of the counterbore depth (W) for securing the stroke (S). ● The dimension of the stopper bolt is set so that the head is recessed 2mm below the mounting plate. (See "Stopper Bolt STBG" on P.915 .) When using a urethane washer, the relationship between the counterbore depth (W) and the stroke (S) is [W = S + Urethane Washer Thickness T + stopper bolt head thickness K + 2].
2
2
Runner stripper plate
0 + 0.1
d
+ 0.1 + 0.2 T ± 0.1 h
0 D
- 0.1
MK
M Material SUS416
RPSK/RPSB RPST E Forming marks sometimes remain on the bottom face of the formed groove. RPSZ
Part Number
Applicable bolt size (M) Selection
T
Changes T dimension tolerance. Code
Type
D
E All pieces are grinded together when 20 pieces or less are ordered. (Although T dimension tolerance is as stated in the left table, variation will be limited within 0.01.)
TK1 TK2 TK3
T Tolerance T
Selection side plate
+ 0.02 0 ± 0.01
25
6
TK1 TK2
10 15 20
0 –0.02
T
TK3
6
30
E Note that designated tolerance of TK alteration is different from that of free washer ( D P.1097 ), For heat insulation and free washer ( D P.1098 ).
15 20 10 15 20
RPSZ
8 10
■ Stopper bolt STBG (P.915) K size table STBG Shaft diameter D Head thickness K 10 8 13 8 16 13 20 13
6
40
15 20 12 20
8 10
RPST
UW
Example
SUS416 has low thermal conductivity and is effective in blocking the heat.
Thermal expansion coefficient [× 10 – 6 /K( ℃ ) ] (100 ℃ )
Thermal conductivity coefficient [ cal/cm ・ sec ・℃] (100 ℃ )
Material
RPSZ
RPSK
RPSB
SUS416
0.058
9.9
S50C
0.120
11.5
1cal/(cm ・ sec ・℃ ) = 418.6W/(m ・ K)
1113
1114
Powered by FlippingBook