SHOT COUNTERS FOR MOLD
E Manufactured by PROGRESSIVE Corporation. Counter View is a trademark of PROGRESSIVE Corporation. PAT.
M–RCC (Embedded type) ① only M–RCCB (External mount type) ①+②
M–CVR (Round compact type)
① Main body
①
②
Count pin
Main body
Shot block
12.7
25
47.6
24.3 20
6.35
18
23.8
Counter Pin
L ± 0.1
Actuator Rod
6
PROGRESSIVE
ID Plates for mold identification
9999980
NP65080
No.8 － 32UNC Inch Screw
5
Serial Number
② Shot Blocks
6.7
Serial Number
① M Material
Glass–filled nylon housing a Accessories Socket Head Cap Screws M4–25 (2 pieces) ID Plates for mold identification Heat–resistant temperature 160°C
② M Material Steel a Accessories Socket Head Cap Screws M4–25 (2 pieces)
E Design is subject to change without prior notice.
M Material
Glass–filled nylon housing
M Material
S45C
Heat–resistant temperature
a Accessories Actuator Rod s Surface treatment Electroless nickel plated
120°C
■ Method of specifying the L dimension
L 0.1mm increments
Part Number M–RCC M–RCCB
Part Number
Part Number M–RCC ( ① only) M–RCCB ( ①+② )
Quotation
Delivery
Order
L ＝ Movable mold plate thickness T + actuator rod protrusion of 4mm E Specify taking into account the tolerance T of the mold plate thickness.
M–CVR
60.0–124.0
E The protruding part of the actuator rod is the stroke of the actuator rod. If the stroke is less than 3.75mm, the counter will not work. Conversely, if the stroke exceeds 4.25mm, the counter may be damaged when the mold closes.
■ Stroke amount
■ Mounting dimensions (reference value) and method M–RCC (Embedded)
Part Number – L M–CVR – 64.2
Quotation
Delivery
Order
M–RCCB (External mount type)
■ Mounting dimensions (reference value) and method
Operating range
(View of movable mold plate side)
M–CVR 1. Bore the holes for the main body and the counter (including the actuator rod) to the dimensions shown in the figure below, from the rear of the movable mold plate. 2. Slot an opening for the display panel of the counter to the dimensions shown in the figure below. 3. Ensure that the actuator rod protrudes 4mm above the parting line and decide L dimension depending on the mold plate thickness. 4. Lightly press–fit the unit from the rear of the mold plate, and screw the actuator rod into the counter pin from the P.L. surface. 5. .Retain the bottom of the counter with the support plate.
Fixed mold plate
Shot Block
P.L.
P.L.
Mold Closed
E The stroke of the count pin required for counter is 4.6mm or more. Conversely, if the stroke exceeds 6.5mm, the counter may be damaged.
Movable mold plate
T
Plate thickness
Main Body
Movable mold plate
＋ 0.12 0
max.R0.75
46.75
＋ 0.25 0
Actuator Rod
41.25
＋ 0.3 ＋ 0.1 28
38
PROGRESSIVE
0000000
E Installation dimension shown in above figure is just for reference purpose.
NP65080
4 ± 0.25
12.5 ± 0.12
max.R0.75
■ Features
Support Plate
Movable mold plate
(Movable mold plate side chart)
■ Features
• Counting is actuated mechanically, no miscount will occur if counter is installed correctly. • Each counter has a different serial number that will be used to identify the shot counter with the mold. E We do not mange serial numbers assigned to the products. Counters are sold in random order. • An ID plate for mold identification is included, on which mold numbers, etc., can be engraved. Apply the adhesive seal at the back of the ID Plate to the front of the counter.
• Counting is actuated mechanically, no miscount will occur if counter is installed correctly. •Each counter has a different serial number that will be used to identify the shot counter with the mold. E We do not mange serial numbers assigned to the products. Counters are sold in random order.
E To ensure reliability, the shot counter is non–resettable. E For mold testing purposes, the 7–digit indicator does not start from 0. (a value of 9999980 will be shown) E Due to the structure of the product, the count of "5" is partially displayed. ( ) ■ Notes
■ Notes
E To ensure reliability, the shot counter is non–resettable. E For mold testing purposes, the 7–digit indicator does not start from 0. (a value of 9999980 will be shown) E M–CVR Counter: Ensure that the actuator rod has a stroke of 4mm ± 0.25.
M － CVR: CounterView TM Shot Counter is a registered trademark of Progressive Components International Corporation, covered by European Patent No. EP726129.
1131
1132
Powered by FlippingBook