ANGULAR PINS
E Sale of economy types (APZ, APZS) has been discontinued. Specify additional ATN processing if you do not want an angled head part.
Part Number – L – N – A AP 25 – 200.0 – N30.0 – A15 APS25 – 200.0 – N30.0 – A15
Order
D
M Material H Hardness
4–8
SKD11
60–63HRC
58HRC– (Induction hardening)
10–50
SUJ2
Quotation
Delivery
AP
( E φ 50 c A ° ± 30´)
E Profile tolerance of SR
0.3
A ° ± 15 ´
Part Number – L – (TC/CM/DKC/DC/KAC/TM) APS 25 – 200.0 – N30.0 – A15 – DC24.5 – DKC – KAC AP 20 – 150.0 – N20.0 – ATN – N – A (ATN)
SR ＝ D/2
(max.2 (When D=4-8, R0.5 or below)
Alterations
SR ＝ D/2
G
1.6
Alterations Code
Spec.
Alterations Code
Spec.
E When D = 25 or more, the pin tip becomes as shown in the drawing on the left. E When head D = 4–8, then R is 0.5 or less.
Head thickness change TC = 0.1 mm increments (Reduces the head thickness to less than standard. The full length remains unchanged.) E T ＞ TC ≧ H/2tan A + 2.0 TC min: Fractions are rounded up to the second decimal place. TC = 13/2tan 18° + 2.0 = 4.112 ⇨ 4.2 Single flat chamfering Changes the head shape from a cone to a single flat cut. E Available when D ≦ 30
C
Performs C chamfering on the edge of the step. (Recess of C–chamfering for assembling: about C0.3) E Available for APS when D ≧ 30 Chamfering is performed as standard for D ≦ 25. Step (D–1) can be designated. TC = 0.1 mm increments Tolerance of the step's external diameter 0 –0.05 E D−0.1 ≧ DC ＞ D−1 E When DC is used SR = DC 2 E Available for APS when D ≧ 30
S
0
CM
T － 0.2
N
S
TC
R ≦ 0.5
TC min.2
N
± 0.2
L
E R may be applicable to the head tip. (R ≦ 0.3)
E Machining may leave a chuck keyhole on one end of the pin in case of D = 20 or 25. Dimensions of the pins with chuck keyholes are values prior to machining of the holes. In case of D = 30 or more, the both ends may have chuck keyholes.
A °
DC
APS (Stepped type)
( E φ 50 c A ° ± 30´)
E Profile tolerance of SR
0.3
KAC
2 D － 1
D － 1 2
SR ＝
max.2 (When D=4-8, R0.5 or below)
SR ＝
G
Tapering 30°
1.6
Adds a 30 ° taper on the edge of step. (Taper for installation) E Available for APS X Combination with CM/DC not available
Press–fit section tolerance alteration Changes Dm 5 → D + 0.005 0 . E Available when D ≦ 30 E Available when N ≦ 200
TM
E When D = 25 or more, the pin tip becomes as shown in the drawing on the left. E When head D = 4–8, then R is 0.5 or less.
DKC
N
＊ C
0
S
T － 0.2
N
S
R ≦ 0.5
± 0.2
L
Sets the angle of the head part to A = 0.
ATN
* For D4–25, C–chamfering is performed on the edges of the steps. (Recess of C–chamfering for assembling: about C0.3)
E R may be applicable to the head tip. (R ≦ 0.3)
E Machining may leave a chuck keyhole on one end of the pin in case of D = 20 or 25. Dimensions of the pins with chuck keyholes are values prior to machining of the holes. In case of D = 30 or more, the both ends may have chuck keyholes.
S
Part Number
0.1 mm increments
f6 (AP)
A 1° increments
D m5
T H
AP APS Type
D
L
N
■ About the head tip
4 15.0– 90.0
4
7 2 1.5
L ± 0.2
+0.009 +0.004
–0.010 –0.018
• Slight R may be applied to the head tip due to head tip angle (A degree) processing. (R ≦ 0.3) • T and L dimensions of the pin attached with R are before attaching R.
5 15.0–100.0
5
8 2.5 2
T － 0.2 0
5
6 15.0–110.0
6
9 3 2.5
A°
8 15.0–130.0
8
114 3.5
+0.012 +0.006
–0.013 –0.022
10 20.0–200.0
10
135 4.5
（ R ≦ 0.3 ）
12 20.0–250.0
12
10
156 5.5
13 20.0–250.0
13
16 6.56
2 ≦ N N ≦ L–T–1 or N=0 (No press–fit section)
+0.015 +0.007
–0.016 –0.027
AP
1–30 ( E If you want A=0, then specify additional ATN processing. )
15 20.0–250.0
15
18 7.57
16 20.0–250.0
16
198 7.5
APS (Stepped type)
13
20 40.0–350.0
20
23
9.5
+0.017 +0.008
–0.020 –0.033
25 40.0–400.0
25
28
30 60.0–500.0
30
35
32 70.0–500.0
10
32
37
10
15
35 100.0–500.0
35
40
+0.020 +0.009
–0.025 –0.041
40 100.0–500.0
40
45
50 200.0–500.0
50
20 55
549
550
E If N = 0 is specified, the shaft diameter will be "D-1".
Powered by FlippingBook