Standard Components For Plastic Mold 2021

ALTERATION GUIDE FOR SLIDE CORES WITH ANGULAR HOLE

Spring hole machining

Stop block processing tapping

（ q ）

A / 2

K °

Alterations

ℓ

＋ 0.2 0

Code

SLNB BOLT M × Pitch

Shape Available for Shape Z only Slide Core Stopper Blocks D P.594 E The range of designation for H in this alteration is as follows. VC + 2 + M/2 ≦ H ＜ T q ＞ ℓ + 4 How to calculate q: (L–F)–{(T–H) ・ tanK} Unit of designation ① VC = Select from the table on the right (VC) ② M = Select from the table on the right X Combination with ZC/BP/SC not available

ℓ

10 – A20 10 – A30 13 – A20 13 – A30 13 – A40 13 – A50 13 – A60 16 – A40 16 – A50 16 – A60

MSB10 M 8 × 1.25

Code

X Combination with BP/VC/SC not available

Shape Available for all shapes

Spring Spring dia. φ Q Applicable heatproof wire springs D P.1157–

Adds holes to house push back springs. Q: Select from the table on the right. • Specify X coordinate from the slider's front face left edge as X0 • For one spring hole, designate the desired XA code and enter 0 for XB. E In order to avoid interference between the spring holes, they must be apart from each other at least 2mm. Up to two holes can be created Unit of designation ① ZC = 1mm increments. However n ＞ 5 ZCmin. = 9, ZCmax. =φ Q × 2 How to calculate n

Spec.

MSB13 M10 × 1.5

12.5

WLH WMH WHH

10 13 16 18

11 14 17 19

MSB16 M12 × 1.75

Spec.

Order PartNumber–A–T–L–D–E–G–F–K–H–VC–M SLFK8AZ – A60 – T48 – L85 – D16 – E30 – G15 – F55 – K17 – H20 – VC10 – M8

③ Q = Select from the upper table on the right. ④ XA, XB = 0.5mm increments Q/2 + 2 ≦ XA

n = cosG × [E + tanG × (T (or H) – J – Q/2) – ZC] – d/2 ② J = 1mm increments Jmin. = Q/2 + 2 Jmax. = T–Q/2–5

Bolt hole machining

A/2 + 2 ≦ XB ＜ A–(Q/2)–2

A ＊＊＊＊

Part Num ber –A–T–L– D –E– G –F–K–H–ZC–J–Q–XA–XB SLFK8AY – A60 – T48 – L85 – D16 – E37 – G15 – F73 – K17 – ZC20 – J10 – Q14 – XA14 – XB38

Order

Alterations

Code

Spec.

＊

Shape Available for all shapes Adds a tap hole for a ball plunger. Applicable ball plungers D P.591 Applicable ball plungers Tap M Depth ℓ

Reference point

Code

Range

Shape Available for all shapes Adds bolt holes for shaft pins. Unit of designation ① SC = Select from the table on the right (M) ② N = 1mm increments 5 ＜ F–N ≦ 8

M 6 M 8 M10 M12

15 20 25 30

ℓ + 2 ＞ T(H) c Tap through hole ℓ + 2 ≦ T(H) c Pilot through hole

BPJ BSJ BSZ

d 1

d 2 5.5 6.5

Applicable bolt M

9.5

11 M6 X Combination with ZC/BP/VC/AM not available

③ XA, YA (coordinates) = 0.5mm increments ④ XB, YB (coordinates) = 0.5mm increments

Spec.

Unit of designation ① BP = Selection (M) from the above table ② XA = 0.5mm increments XA designation range XAmin. = M/2 + 2, XAmax. = E – (M/2 + 3) ③ XB = 0.5mm increments XB designation range XBmin. = M/2 + 2, XBmax. = A – (M/2 + 3) Specify XA, XB coordinates from the slider's front face left edge as X0. Only one hole can be created X Combination with ZC/VC/SC/AM not available

2mm or more

Specify X, Y coordinates from the slider's front face left edge as (X0, Y0). Designate so that the section marked with ＊ will be 2mm or more. ( A + d + d 1 )/2 + 2 ≦ XB Set YA 1mm or longer than the slide core's head thickness. However it should as follows for Shapes X and Z: H + d 1 /2 + 2 ≦ YA, YB

Order PartNumber– A – T – L – D – E –G– F–K–H–SC–N–XA–YA–XB–YB SLFK8AY – A60 – T48 – L85 – D16 – E30 – G15 – F73 – K17 – SC5 – N65 – XA9.0 – YA18.0 – XB51.0 – YB39.0

Pilot hole diameter

Alterations

Code

Spec.

Shape Available for all shapes Adds oil groove for slide core lower surface. E Available when W–d 2 ≧ 10, L ≧ 40 E L ＞ W–d 2 c θ ° = 90° L ≦ W–d 2 c θ ° = 60° Designation method AM X Combination with BP/SC not available

Tap M

θ°

PartNumber–A–T–L–D–E–G–F–K–H–BP–XA–XB SLFK8AY – A60 – T48 – L85 – D16 – E30 – G15 – F73 – K17 – BP12 – XA8.5 – XB20.0 PartNumber–A–T–L–D–E–G–F–K–H–HC SLFK8AZ – A60 – T48 – L85 – D20 – E20 – G15 – F70 – K17 – H20 – HC64

Order

Part Num ber –A–T–L–D–E–G–F–K–H–AM SLFK8AZ – A60 – T48 – L85 – D16 – E30 – G15 – F55 – K17 – H20 – AM

Order

589

590