TAPERED BLOCK SETS
■ Standard Match mark type
Part Number
Bolt hole Installation bolts ℓ 2 d t
No. of bolt holes 1 (Tapping hole) 1 (Tapping hole)
Dismounting tap N
Tapping hole M × ℓ
L Selection
K° Selection
V E T T 1 T 2
Type
A
ℓ 1
15 20 20 25 20 25 30 40 20 25 30 40 25 30 40 30 40 50 40 50 75
M3 × 6
12
7 * 5
M3 Bolt
M 3
– –
M4 × 6
16
M4 Bolt
M 4
9
– –
23 714
1
* 7
20
6.5 3.5 M3 Bolt
M 4
12
7.5 15 10 20
2
1 3 5
1
– –
25
8 5
M4 Bolt
M 5
28 917
15
7.5 15 10 20 – – 7.5 15 10 20 7.5 15
2
Precision Rank
V dimension symmetry against A plane (Match mark type) Because of add fitting processing, not applicable to combinations other than sets 0.005 or less It can be used without worrying about the set combina- tion or direction.ex) 2–color molding, insert molding, etc.
Part Number
T A Tolerance
M Material
H Hardness
8
TBS
Set
Pin only Bushing only
1
30
17
32 10 20
+ 0.02 0 0 –0.005
9 6
M5 Bolt
M 6
TBS
–
–
Standard
SKD11 equivalent
–
58–62HRC
VTBS
VTBSP
VTBSB
Precision
35
20 10351122
20 30 20 30
10
11 7
M6 Bolt
M 8
2
■ Mounting bolt holes: 2 (L30–120)
■ Mounting bolt hole: 1 (A20 and above, when L20–25)
45
25 15451429
① Pin
① Pin
② Bushing
② Bushing
17.5 40 20 60 15 30 20 50 30 60
+ 0.1 + 0.3
+ 0.1 + 0.3
+ 0.1 + 0.3
+ 0.1 + 0.3
4 - C3
4 - C3
100
A
A
3 5
4 - C3
4 - C3
A
A
60 90
65
14 9
M8 Bolt
M10
35 20601939
120
E The height of the pin is E + 1mm for A12/A16.
■ Precision
Dismounting tap N
Bolt hole
Part Number
No. of bolt holes
Installation bolts
K° Selection
L Selection
V E T T 1 T 2
d t
Type
A
ℓ 2
ℓ 1
0 –0.3 –0.2 –0.5
L ≦ 50 c ※ L L ≧ 60 c ※ L
25 30 25 30
– – 7.5 15 – – 7.5 15
1 2 1
VTBS (Set ①+② ) VTBSP ( ① Pin) VTBSB ( ② Bushing)
V d
2 - C0.5
20
12 723 714
6.5 3.5 M3 Bolt
M4
K °
V d
2 - C0.5
K °
2 - C0.5
1 3 5
2 - C0.5
25
15 828 917
8 5
M4 Bolt
M5
d
d
30 40 35 40
17 8321020 20 10 35 11 22
9 6 11 7
M5 Bolt M6 Bolt
M6 M8
2
10 20
■ When using
4 - C1
4 - C1
4 - C1
4 - C1
N
N
N
N
Mounting tap hole 1 (A12/16)
Mounting bolt hole 1/2 (A20–65)
(Dismounting tap)
(Dismounting tap)
(Dismounting tap)
(Dismounting tap)
Relief
About mounting bolt hole (N): 1 or 2 As shown in the figure on the left, the block can be easily removed by screwing a bolt into its tapping part to extract it.
■ Mounting bolt hole: 1 (A12/16 only)
A12 c ※ C2 A16 c ※ C3
PL
① Pin
② Bushing
Mount as shown in the figure on the left. Make sure to provide the embedding hole with recesses as shown in the figure above.
+ 0.1 + 0.3
0.1 + 0.3
※ 4 - C
4 - C
※ +
A
A
● Dimensions when setting
Match mark
When assembling, if the matching taper is large, it may be necessary to adjust the height of the taper so that they fit more tightly, but if the matching taper is small, it is necessary to take sticking of the pin into consideration. At 1°taper (also 3°taper in some cases), sticking can be avoided by setting them slightly afloat as shown in the figure on the left. When the angle is small, the creep of the height (a in the left drawing) against the width (b in the left drawings) is also small, so there is no need to worry about positioning inaccuracies.
a
( Value b to error a )
a
0.1
0.3
0.5
• There is a match mark on the 'MISUMI' logo side, facilitating position alignment. • Set the blocks so that the 'MISUMI' logo is visible from outside of the mold. E TBS must be used in set combination and direction being preset upon delivery. E VTBS has only the 'MISUMI' logo. It does not have a match mark.
Angled
V
2 - C0.5
K °
1° 3°
0.0018 0.005 0.009 0.005 0.016 0.026
2 - C0.5
b
* Arrows indicate direction of thermal expansion
■ The tapered block sets are capable of offsetting the plate's thermal expansion caused in high temperature molding processes for thermosetting resins, etc., thereby maintaining positioning accuracy. The pin type positioning method cannot thoroughly absorb thermal expansion when it takes place in directions as shown in the figure on the left. The block type will be unaffected if the groove direction is in parallel to the directions of thermal expansion as shown in the drawing.
M ×ℓ
4 - C1
4 - C1
M ×ℓ
E The height of the pin ① is E + 1mm.
Cavity
Part Number – L – K TBS35 – 40 – 3 VTBS25 – 30 – 1
Quotation
Delivery
Order
853
854
Powered by FlippingBook