MAGNET LOCK SETS −NORMAL TYPE/COMPACT TYPE−
■ Normal type Part Number
MLK
Normal Type
M Material SS400 magnet
Identification collar
Adhesion strength (per set under 20°C)
MLK40/100 Neodymium magnet (Heat resistance: 80°C or less) MLK80/200 SmCo magnet (Rare earth) (Heat resistance: 200°C or less)
A B S L T t
D 1
D 2
d 1
d 2
a Accessories
392.3N {40kgf} 784.5N {80kgf} 980.7N {100kgf} 1961.3N {200kgf}
Gold (Brass)
MLK 40
■ Holder
A
CB8-25
4 pcs. 4 pcs.
63 25
60 802512
18 22
9 14
Spring washers
Silver (Aluminum)
MLK 80
Gold (Brass)
MLK100
CB10-30
4 pcs. 4 pcs.
100
39
79
126 40
15 30
34
11 18
Spring washers
MLK200 Silver (Aluminum) E Adhesion strength per set indicates the vertical force by which a holder and a block adhered each other can be separated. ■ Features • Is easier to install compared with other types of mold locking units. • Requires little slowing down for mold closing. (making the molding cycle more efficient) E One set consists of one holder and one block. ■ Compact type Part Number A S L T D 1 D 2 d 1 d 2
2 －φ D 2 (Identification collar) 2 －φ D 1 (Magnet)
d
2
A
G
L S B
d
Adhesion strength (per set under 20°C)
Identification collar
1
1.6
a Accessories
0.01 A
196.1N {20kgf} 392.2N {40kgf} 490.3N {50kgf} 980.6N {100kgf}
Gold (Brass)
30
MLKC 20
CB6–25
4 pcs. 4 pcs.
■ Block
d 2
15
36 36
50 25
18 22
6.6
11
Spring washers
Silver (Aluminum)
MLKC 40
Gold (Brass)
MLKC 50
A
CB8–30
4 pcs. 4 pcs.
52 52 70 40
30
34
9
14
Spring washers
MLKC100 Silver (Aluminum) E Adhesion strength per set indicates the vertical force by which a holder and a block adhered each other can be separated. ■ Features • MLKC40/100 is about 50%–60% smaller than normal type (MLK). • Is easier to install compared with other types of mold locking units. • Requires little slowing down for mold closing. (making the molding cycle more efficient) E One set consists of one holder and one block.
G
d 1
1.6
L A
0.01 A
M Material SS400
Compact Type
MLKC
M Material SS400 magnet
MLKC20/50 Neodymium magnet (Heat resistance: 80°C or less) MLKC40/100 SmCo magnet (Rare earth) (Heat resistance: 200°C or less)
A
Part Number MLK80 MLKC100
Order
■ Holder
Quotation
Delivery
φ D 2 (Identification collar) φ D 1 (Magnet)
d 2
■ How to mount • Place magnet lock sets onto the mold's center, and fasten with the supplied bolts. • Install them so that the magnetic face is in parallel to the parting line. • Finish the plate surfaces so that the lock's magnets tightly couple together. • Use MSB Shoulder Bolts if bolt breakage is anticipated D P.1106 To use a MSB Shoulder Bolt, make sure to create a counterbore on the plate. Finish the counterbore into H7 or so.
A
MSB
G
d 1
1.6
S L
Example
0.01 A
Closed state
Open state
30
■ Block
d 2
15
A
G
1.6
d 1
A L
0.01 A
M Material SS400
933
934
Powered by FlippingBook